TPR Peel Rivet | TPR-L-6,3
TPR Peel Rivet TPR-L-6,3
- CE (ETA-08/0262)
Material Fastener
Aluminium/Magnesium Alloy
Material Mandrel
Carbon steel, galvanised
Diameter Fastener [mm]
6.3
Product Type
Peel Rivet
Material
Aluminum-magnesium
Diameter
1/4"
Loading Bearing Length [Inches]
1-5/8" – 3", 1/2", 1/2" – 1", 2-5/8" – 4", 3-5/8" – 5", 4-5/8" – 6", 5-5/8" – 7", 6-5/8" – 8", 7-5/8" – 9", 7/8" – 2"
- Ideal for insulation and membrane attachment to problematic roof decks
- For use in roof decks where threaded fasteners cannot achieve required pull out values
- For use in corrosive building environments
- Two-piece, aluminum-magnesium alloy fastener
- Low profile mushroom head
- High pull out values
- Cannot be over-tightened
- Consistent structural performance
- One fastener can accommodate a wide range of material thicknesses
- Safe and successful installation every time
- Constructed from a highly corrosion resistant aluminum- magnesium alloy
- A specially designed pulling tool is required for all installations and is available in pneumatic and hand operated models.
- Minimum of 1" penetration required in steel, wood fiber, wood, and lightweight concrete.
- Pre-drill diameter for all substrates is 9/32" (7 mm). Note: reduce maximum clamping length by 1/4" when fastening to wood fiber or fragile substrates.
- Material
- Steel; Min penetration 1"
- Wood; Min penetration 1"
- Wood fiber; Min penetration 1"
- Lightweight concrete; Min penetration 1"
- Use with
- isoweld TPO or PVC plates
- 2" or 3" round Galvalume stress plates
- 2-7/8" hex Galvalume stress plates
TPR Peel Rivet | TPR-L-6,3
TPR Peel Rivet TPR-L-6,3
- CE (ETA-08/0262)
Material Fastener
Aluminium/Magnesium Alloy
Material Mandrel
Carbon steel, galvanised
Diameter Fastener [mm]
6.3
Product Type
Peel Rivet
Material
Aluminum-magnesium
Diameter
1/4"
Loading Bearing Length [Inches]
1-5/8" – 3", 1/2", 1/2" – 1", 2-5/8" – 4", 3-5/8" – 5", 4-5/8" – 6", 5-5/8" – 7", 6-5/8" – 8", 7-5/8" – 9", 7/8" – 2"
- Ideal for insulation and membrane attachment to problematic roof decks
- For use in roof decks where threaded fasteners cannot achieve required pull out values
- For use in corrosive building environments
- Two-piece, aluminum-magnesium alloy fastener
- Low profile mushroom head
- High pull out values
- Cannot be over-tightened
- Consistent structural performance
- One fastener can accommodate a wide range of material thicknesses
- Safe and successful installation every time
- Constructed from a highly corrosion resistant aluminum- magnesium alloy
- A specially designed pulling tool is required for all installations and is available in pneumatic and hand operated models.
- Minimum of 1" penetration required in steel, wood fiber, wood, and lightweight concrete.
- Pre-drill diameter for all substrates is 9/32" (7 mm). Note: reduce maximum clamping length by 1/4" when fastening to wood fiber or fragile substrates.
- Material
- Steel; Min penetration 1"
- Wood; Min penetration 1"
- Wood fiber; Min penetration 1"
- Lightweight concrete; Min penetration 1"
- Use with
- isoweld TPO or PVC plates
- 2" or 3" round Galvalume stress plates
- 2-7/8" hex Galvalume stress plates